As an Amazon Associate, Akermin earns from qualifying purchases. Product links on this page are affiliate links.
For methane, one percent of the lower explosive limit equals five hundred parts per million, so dividing a ppm figure by five hundred gives the flammability percentage and multiplying by five hundred reverses it. The constant comes from two published facts and nothing else: one percent by volume is ten thousand parts per million, and methane will not propagate a flame below about five percent by volume. Those give a full scale of fifty thousand parts per million spread across a hundred divisions. The conversion is only valid for methane, and only when the instrument producing the reading is referenced to methane.
Three units, one quantity, two multiplications
Parts per million, percent by volume and percent of the lower explosive limit all describe how much fuel is mixed into the air. Moving between the first two is a pure change of unit: a million divided by a hundred is ten thousand, so one percent by volume is ten thousand parts per million and the conversion never changes for any gas or any condition.
Moving to the third unit is where substance specific information enters. Dividing by a flammable limit turns an absolute composition into a position on a hazard scale, and the divisor is a physical property of the fuel. That single step is the reason the third unit cannot be converted without naming the gas, while the first two can be converted blind.
Written as a chain it is short. Take the ppm figure, divide by ten thousand to get percent by volume, divide by the flammable limit of the gas and multiply by a hundred to get the flammability percentage. For methane the two divisions collapse into one constant, which is what makes the mental arithmetic easy. The same chain in the other direction and across other gases is laid out on the ppm, LEL and volume page.
The methane numbers that make the arithmetic work
Three published figures carry the whole calculation. Methane has a lower flammable limit near five percent by volume. One percent by volume is ten thousand parts per million. Therefore full scale on a methane flammability display is fifty thousand parts per million, and each of the hundred divisions on that display is five hundred parts per million.
From that constant everything else is a one line sum. A thousand parts per million is two divisions, or two percent of the flammable limit. The conventional first alarm at ten divisions is five thousand parts per million, or half of one percent of the atmosphere. Twenty five thousand parts per million is halfway to ignitable. And the top of the display, one hundred divisions, is the five percent by volume where a flame can first sustain itself.
It is worth noticing how small all of these are as fractions of the air. Even at the top of a flammability display, the atmosphere is ninety five percent its ordinary self. That is a useful corrective when a reading of forty or fifty on a scale instinctively feels like half the room is gas.
A conversion table you can read in either direction
| Parts per million | Percent by volume | Percent of the lower explosive limit | What it corresponds to |
|---|---|---|---|
| 100 | 0.01 | 0.2 | Below the first division of most flammability displays |
| 500 | 0.05 | 1 | One division, the smallest step many instruments show |
| 1,000 | 0.1 | 2 | A leak large enough to read on a coarse scale |
| 2,500 | 0.25 | 5 | Halfway to the conventional first alarm |
| 5,000 | 0.5 | 10 | The conventional first alarm point |
| 10,000 | 1.0 | 20 | A common second alarm point |
| 25,000 | 2.5 | 50 | Half the distance to an ignitable mixture |
| 50,000 | 5.0 | 100 | The leanest methane mixture that will carry a flame |
Read the table in either direction and the pattern of the constant is visible down the first and third columns. It is also a reminder of how far apart leak searching and atmosphere monitoring sit: the top two rows are the territory of a probe, and the bottom three are the territory of an evacuation.
Calibration gas and why the conversion can be wrong
A catalytic sensor is adjusted so that a certified concentration of one reference fuel produces the correct scale reading. Methane and pentane are both common reference gases, and an instrument spanned on one of them does not respond identically to the other fuels it will meet. Manufacturers publish correction factors for exactly this reason, and applying the methane arithmetic to an uncorrected reading taken in propane produces a number that is confidently wrong.
Infrared sensing has the same dependency in a different form, since the absorption band and its strength differ by molecule, and hydrogen is invisible to it entirely. The practical effect is identical: the units on the display belong to the gas the instrument was set up for, and the conversion constant belongs to the gas actually present. When those two are not the same substance, the sum needs a correction factor before it needs anything else.
This is also where the familiar indoor use of parts per million can mislead by association. Carbon dioxide indoors is discussed in the same unit, and the page on what a thousand parts per million means for carbon dioxide deals with a concentration that is significant for ventilation and nowhere near any flammability question. Same unit, unrelated hazard, no shared arithmetic.
A published range that does not reconcile
Listings sometimes print both scales side by side, which is helpful when the pair agrees and informative when it does not. The TopTes PT205 states detection from one to ten percent of the lower explosive limit, with a bracketed equivalent given as one hundred parts per million to five thousand parts per million, based on methane. The upper endpoint is exactly right: ten divisions of a methane scale is five thousand parts per million. The lower endpoint does not follow the same arithmetic, because one division of a methane scale is five hundred parts per million, and one hundred parts per million is a fifth of a division.
The useful response is not to distrust the instrument but to trust the display over the bullet. Two published endpoints derived from the same constant should both reconcile, and when one does, the other is best treated as loosely written. Checking both ends of any published pair takes a few seconds and catches this class of error reliably.
Other instruments avoid the question by not offering a flammability scale at all. The MSA ALTAIR 2X single gas detector in its hydrogen sulphide variant states a low alarm at five parts per million and a high alarm at ten parts per million, with event and data logging, bump and calibration records and IP67 construction. Those thresholds are toxic thresholds, and since the flammable limit of that gas sits at tens of thousands of parts per million, no conversion to a flammability scale is relevant to how it is used. The BW Technologies GasAlertMicroClip XL carries a combustible channel alongside three others, and the units that channel displays are Not stated in the listing bullets, which is the first thing to establish before any conversion is attempted.
Doing the conversion in your head at the valve
Keep three things in working memory and the sum needs no paper. One percent by volume is ten thousand parts per million. Methane ignites from about five percent by volume. One division of a methane flammability scale is five hundred parts per million. Everything on this page is a consequence of those three statements.
Then apply the two checks that stop the arithmetic from being applied where it does not belong. Confirm the gas present is the gas the instrument is referenced to, and confirm the units on the display before converting anything. If either is uncertain, the reading is still a valid indication that something is leaking and is not yet a quantity. For the detectors covered in the Smart Sensor carbon monoxide meter review and similar single gas instruments, the displayed unit is the whole specification, and reading it correctly is most of the work.
Frequently Asked Questions
What is the single number to remember for methane?
Five hundred parts per million for every one percent of the lower explosive limit. Divide a ppm figure by five hundred to get the flammability percentage, multiply a flammability percentage by five hundred to get ppm. That constant comes from a flammable limit of five percent by volume, which is fifty thousand parts per million spread across a hundred scale divisions.
Does the same constant work for propane?
No. Propane has a lower flammable limit of about two point one percent by volume, so one percent of its scale is about two hundred and ten parts per million rather than five hundred. Every fuel has its own constant because every fuel has its own flammable limit, and using the methane constant on propane overstates the margin remaining by well over a factor of two.
Why does the calibration gas of an instrument change the answer?
Because a catalytic sensor does not respond equally to every fuel. The instrument is adjusted so that a known concentration of one reference gas produces the correct scale reading, and any other fuel produces a response that is higher or lower in a ratio published as a correction factor. Reading propane on an instrument spanned with methane gives a number that has to be corrected before the conversion arithmetic means anything.
Is parts per million by volume the same as parts per million by weight?
Not for gases, and the distinction matters when converting to milligrams per cubic metre. Gas concentrations in air are normally quoted by volume, so one part per million means one volume of gas in a million volumes of mixture. Converting that to a mass based unit requires the molar mass of the gas and the temperature and pressure of the mixture, which is a different calculation from the one on this page.
What should I do when a listing publishes two figures that do not agree?
Treat the pair as unverified and work from the scale the instrument actually displays. A conversion printed in a bullet is a convenience rather than a measurement, and an endpoint that does not reconcile with the flammable limit of the stated gas usually means the bullet was written loosely rather than that the instrument behaves strangely. The manual, or the figures on the display itself, settle it.
Does humidity or temperature change the conversion?
The conversion between parts per million and percent by volume is a pure ratio of volumes and does not move. What can move is the response of the sensor producing the reading, since catalytic and infrared elements both have temperature coefficients and humidity can affect some sensing chemistries. The arithmetic is stable and the measurement feeding it is the part that carries conditions.