As an Amazon Associate, Akermin earns from qualifying purchases. Product links on this page are affiliate links.
LJPXHHU · Digital Multimeter Voltmeter Battery Voltage Multi Tester Continuity Ohm Volt Amp DC AC Current Resistance Diodes 2000 Counts Electrical Test Meter with Leads Backlight LCD Display
View on AmazonPrice and availability are shown on Amazon and can change at any time.
The LJPXHHU is a general-purpose handheld multimeter for basic voltage, resistance, continuity, diode, and DC current checks around cars and household wiring. Its 2000-count display gives a best resolution of about 1 mV on the lowest DC voltage range, which is fine for confirming a 12 V battery or a wall outlet but not for measuring millivolt drops on a ground circuit. The listing does not publish a CAT safety rating, a DC current range, or an accuracy figure, so treat it as a learning and diagnostic meter rather than a locked-off panel instrument. Buy it if you need a cheap second meter or a first meter for low-energy work; do not buy it if you work on live distribution panels or need to document accuracy.
What “2000 Counts” Actually Limits
The single specification in this listing that decides whether the meter suits a job is the display count. A 2000-count meter can show values from 0 to 1999 before it rolls over to a higher range. That sounds like a marketing footnote, but it sets the smallest change the meter can display on each range.
On the lowest DC voltage range, a 2000-count display typically resolves 1 mV. That is enough to see a 12 V battery fall from 12.6 V to 12.2 V under load, and enough to confirm that a wall outlet is live. It is not enough to measure the millivolt drop across a ground strap or a fuse holder, where a fault may show as 20 mV or 40 mV. For that work you need a meter with more counts or a dedicated low-resistance instrument.
The listing does not publish the actual range boundaries or the accuracy specification. So you know the count class but not the measurement uncertainty. If you need to know whether a reading is within 0.5 percent or 2 percent, this listing cannot tell you.
The Safety Question the Listing Does Not Answer
The bullets promise overload protection on all ranges and double insulation. Those are useful construction details. They are not the same as a CAT rating. A CAT rating states the transient voltage the meter can survive when connected to a particular part of an installation, for example CAT II for wall outlets or CAT III for distribution panels.
The LJPXHHU listing does not publish a CAT rating. That omission matters because the same meter may be safe on a bench and unsafe in a panel. Without a published rating, you should not treat this instrument as suitable for work on live distribution boards or service entrances. It is a reasonable meter for low-energy circuits, automotive checks, and learning.
If you need to understand what a CAT rating covers, the site explains it in what a CAT rating on an electrical meter means. The short version: the number describes where the meter may be used, not how well it is built.
What the Bullets Do and Do Not Publish
The listing states AC and DC voltage, DC current, resistance, continuity, diode test, and battery test. It gives a 2.7 inch backlit LCD, data hold, a fold-out stand, a removable rubber cover, a 9 V battery, test leads, and a two-year guarantee.
It does not publish the DC current range, the AC current range, the resistance range, the accuracy, the input impedance, or the CAT rating. Those are the figures a technician uses to decide whether a meter is adequate. The listing also does not state whether the meter is auto-ranging or manual-ranging. That is a usability difference: manual ranging means you select the range yourself, which is slower but predictable.
Because those figures are absent, this review cannot confirm that the meter will measure the current you need. If your job involves measuring more than a few hundred milliamps of DC current, ask the seller for the published range before buying.
Where This Meter Fits in Real Work
The LJPXHHU is aimed at car repair, household checks, schools, and beginners. For those uses, the feature set is coherent. A backlit display helps in a dim garage. Data hold lets you capture a reading you cannot see while your hands are busy. A fold-out stand lets you set the meter down and read it from a distance. The rubber cover protects against minor drops.
It is not a clamp meter, so measuring current requires breaking the circuit and putting the meter in series. If you mainly want to measure current without disconnecting anything, a clamp meter is the right tool. The site compares the two approaches in multimeter versus clamp meter.
It is also not a battery capacity tester. Checking a 12 V battery with a multimeter tells you its resting voltage, not its ability to deliver current. For that distinction, see how to test a 12 V battery with a multimeter.
Continuity, Diodes, and the Limits of a Cheap Probe
Continuity mode gives an audible tone when resistance is low. The listing calls it an audible continuity sensor. That is useful for tracing wires and checking fuses. The listing does not state the threshold resistance at which the tone sounds, so you cannot know whether a 50 ohm connection will beep. In practice, a continuity beep confirms a path exists; it does not confirm the path is good enough for a high-current circuit.
Diode test applies a small voltage and shows the forward drop. The listing does not publish the test current or voltage. That means you can use it to check a silicon diode in one direction, but you cannot rely on the exact number to match a datasheet.
These are normal limitations for an inexpensive meter. The mistake is to treat a continuity beep as a pass result for a safety-critical ground. A low-resistance measurement with a dedicated instrument is the correct check.
Maintenance and the Battery Compartment
The listing states that the 9 V battery is included and that the compartment lid at the back is easy to remove. It also states low battery indication. Those are the maintenance facts published. What the listing does not state is whether the meter has a fuse on the current ranges. Overload protection is claimed on all ranges, but the specific protection method is not described.
If you measure current and make a mistake, a fused input is what saves the meter. Without a published fuse specification, you should treat the current ranges with care and avoid leaving the meter connected in current mode across a voltage source. That is the common way inexpensive meters are destroyed.
The rubber cover is removable. Removing it makes the meter thinner but gives up the drop protection. Keep the cover on if the meter lives in a tool bag.
Should You Buy the LJPXHHU?
Buy the LJPXHHU if you need a first meter or a spare for low-energy checks: automotive voltage, continuity, diode tests, and household outlet confirmation at a basic level. The 2000-count display is adequate for those tasks, and the backlight and stand are genuinely useful in a garage.
Do not buy it if you work on live distribution panels, need a published CAT rating, need to measure more than a small DC current, or need documented accuracy. The listing does not publish those figures, and no review can invent them. If your work requires a CAT III or CAT IV rating, choose a meter that states one.
For a step-by-step guide to selecting a meter for this kind of work, see how to choose a digital multimeter.
Recommended Tools
Products shown because their documented specifications fit this guide. Price and availability are on Amazon and can change.
Frequently Asked Questions
What does 2000 counts mean on this multimeter?
It means the display can show values up to 1999 before moving to a higher range. On the lowest DC voltage range that typically gives 1 mV resolution. It is enough for basic battery and outlet checks but not for measuring small voltage drops in millivolts.
Does the LJPXHHU have a CAT safety rating?
The listing does not publish a CAT rating. Without one, you should not assume it is suitable for live distribution panels or service equipment. Treat it as a low-energy diagnostic meter.
Can it measure current with the clamp?
No. This is a multimeter with test leads, not a clamp meter. To measure current you must break the circuit and connect the meter in series. The listing does not publish the maximum current range.
Is the 9 V battery included?
Yes. The listing states that a 9 V battery, test leads, and a user manual are included.
What accuracy does the meter have?
The listing does not publish an accuracy specification. That means you cannot know the measurement uncertainty from the product data. For work that requires documented accuracy, choose a meter that publishes it.
Is it suitable for a beginner?
Yes, for low-energy learning and basic checks. The backlit display and data hold make it easy to read. But a beginner should not use it on live panel work, because the CAT rating is not published.
Affiliate disclosure: Akermin earns a commission from qualifying Amazon purchases made through links on this page. Our editorial picks are based on documented specifications and owner feedback, not commissions.
Related Guides
Fluke FLUKE-369 FC Leakage Current Clamp Meter Review: What the Listing Leaves Out
A source-led review of the Fluke 369 FC that highlights the unpublished specifications and their practical consequences.
Read More→
HiLetgo LCR-T4 Component Tester Review: The First Hour
A first-hour review of the HiLetgo LCR-T4 kit, covering what it measures, what the listing leaves out, and when a different instrument is the better answer.
Read More→
Klein Tools CL900 Clamp Meter Review: What the Listing Leaves Out
A specification-by-specification review of the Klein Tools CL900 that flags every gap in the published listing.
Read More→