As an Amazon Associate, Akermin earns from qualifying purchases. Product links on this page are affiliate links.
TempPro · TempPro TempScan Infrared Thermometer Gun with 2 Laser for Pizza Oven Grill | 16:1 D:S Ratio Temperature Gun for Cooking HVAC Engine, Laser Thermometer Gun with Adjustable Emissivity Temp Gun -58℉-1022℉
View on AmazonPrice and availability are shown on Amazon and can change at any time.
The TempPro TempScan is a non-contact infrared thermometer with a 16:1 distance-to-spot ratio, dual laser targeting, adjustable emissivity from 0.1 to 1.0 and a stated accuracy of plus or minus 1.5 percent. That ratio is the specification to lead with: it means the measurement spot grows by roughly one unit for every sixteen units of distance, so at 80 cm the spot is about 5 cm across. If your work involves measuring a small target from a safe distance, such as an oven interior or a hot engine part, that matters more than the laser count. The listing does not publish a temperature range, a response wavelength or a resolution figure, so those remain open questions.
Why the 16:1 ratio is the number that decides the job
Infrared thermometers do not measure a point. They average the infrared energy over a circular area called the spot, and the size of that spot grows with distance. The distance-to-spot ratio tells you how fast. A 16:1 ratio means that at 16 units from the target, the spot is 1 unit across. At 80 cm, the spot is about 5 cm. At 1.6 m, it is about 10 cm.
That geometry sets the limit on what you can measure. A pizza stone is wide, so a 5 cm spot at 80 cm is fine. A grill grate is thin, so the spot may straddle the metal and the air behind it, and the reading will be a blend rather than the surface temperature. An HVAC vent louver is narrow, so measuring it from across the room with a wide spot gives you an average of louver and surrounding wall. The dual laser thermometers category exists largely because the two beams show you the spot edges, and the TempScan uses two lasers for that purpose.
The listing states the 16:1 ratio and the two lasers, but it does not state the minimum spot size at close range or the distance at which the optics focus. Those are the figures that would tell you whether the gun is usable on a 1 cm target at 15 cm. They are not published, so treat close-range small-target work as unconfirmed until you can check the manual.
What the listing actually publishes, and what it leaves open
The published figures are: accuracy of plus or minus 1.5 percent, adjustable emissivity from 0.1 to 1.0, a 16:1 distance-to-spot ratio, a 0.5 second response time, and MAX/MIN/AVG display. Those are the numbers you can rely on. The listing does not publish a temperature measurement range, a spectral response, a resolution, an operating temperature, a battery type or a warranty period.
The missing temperature range is the most consequential gap. A pizza oven and a grill both run hot, and an engine block can exceed the range of a general purpose gun. Without a published upper limit, you cannot confirm from the listing alone that the instrument will read your oven at its working temperature. The 0.5 second response time is stated, and it is useful for scanning a smoker or tracking a cooling engine because the display updates quickly enough to follow change rather than lag behind it.
Emissivity from 0.1 to 1.0 is a genuine adjustment, not a fixed setting. Emissivity describes how efficiently a surface radiates infrared energy, and shiny metal radiates poorly. A gun set to the wrong emissivity will misread bare aluminium or polished steel. The adjustable range lets you compensate, but only if you know the emissivity of the surface you are measuring.
Cooking, HVAC and automotive: three jobs, one geometry
The listing pitches the TempScan at pizza ovens, griddles, HVAC vents and overheating engine parts. Those three jobs stress the 16:1 ratio in different ways. In cooking, the target is usually large and the distance is short, so the ratio is comfortable. A griddle is a broad flat surface, and a pizza oven floor is wide enough that a 5 cm spot at 80 cm is representative. The cooking and grills use case is the one where this instrument is least likely to mislead you.
In HVAC, the target is often a vent louver or a refrigerant line. A louver is narrow, and a line is small in diameter, so the spot size at the distance you can safely stand becomes the limiting factor. The MAX/MIN/AVG function helps here because you can sweep a register and see the range rather than a single snapshot. The HVAC thermometers comparison is the right place to check whether a narrower spot at close range suits your work better.
In automotive work, the target is an engine part that may be small and shiny. Small targets need a short distance, and shiny metal needs emissivity compensation. The listing states the emissivity range, so the second problem is addressable. The first is not solved by the ratio alone; it depends on the minimum focus distance, which the listing does not publish.
Where a single-point thermometer stops being the right answer
An infrared thermometer gives you one number for one spot. It cannot show you a temperature gradient across a wall, a hot cell in a battery pack or a cold bridge in a ceiling. Those jobs need an imaging device that maps many spots at once. The thermal camera versus infrared thermometer comparison sets out the boundary, and it is worth reading before you buy a gun for diagnostic work that is really about finding where the heat is.
The TempScan is a spot instrument. It is well suited to confirming a temperature you already expect, such as a grill surface or a vent output. It is poorly suited to discovering an unexpected temperature pattern, because you would have to scan point by point and remember the readings. The MAX/MIN/AVG function softens that limitation by summarising a sweep, but it does not replace an image.
The listing also makes no claim about alarm functions. This is a meter, not an alarm. It will not warn you when a temperature crosses a threshold while you are not looking.
The verdict on the TempScan
The TempPro TempScan is a sensible choice when your target is large enough for a 16:1 spot and your distance is modest. Cooking surfaces and griddle checks fit that description well. HVAC vent sweeps fit it if you accept that a narrow louver will be averaged with its surroundings. Automotive work fits it only when the part is large enough and you set emissivity for shiny metal. The listing does not publish a temperature range, so confirm the upper limit against your oven or engine before relying on it. The dual lasers and adjustable emissivity are useful, but the ratio is the specification that decides whether this gun suits the job at all.
Recommended Tools
Products shown because their documented specifications fit this guide. Price and availability are on Amazon and can change.
Frequently Asked Questions
What does the 16:1 distance-to-spot ratio mean in practice?
It means the measurement spot grows by one unit for every sixteen units of distance. At 80 cm the spot is about 5 cm across; at 1.6 m it is about 10 cm. Any target smaller than the spot at your working distance will be averaged with its surroundings.
Does the listing state the temperature range?
No. The listing does not publish a measurement range. That is the figure to confirm before buying if you intend to use it on a pizza oven or an engine at high temperature.
What are the two lasers for?
They show the edges of the measurement spot so you can aim at the right area. They do not measure temperature themselves; the infrared sensor does that.
Can it measure shiny metal accurately?
Emissivity is adjustable from 0.1 to 1.0, which lets you compensate for low-emissivity surfaces such as bare aluminium. You need to know the emissivity of the surface to set it correctly; the listing does not supply a table.
Is it an alarm or a data logger?
No. The listing describes a handheld meter with MAX/MIN/AVG display. It does not state alarm functions or logging, and it will not warn you of a threshold crossing while unattended.
Does the listing state accuracy in degrees?
It states plus or minus 1.5 percent, which is a percentage of reading rather than a fixed degree figure. The listing does not publish a separate degree accuracy or a resolution.
Affiliate disclosure: Akermin earns a commission from qualifying Amazon purchases made through links on this page. Our editorial picks are based on documented specifications and owner feedback, not commissions.
Related Guides
Wagner Meters Orion 950 Pinless Wood Moisture Meter: A Review for Thermal Inspection Work
A review of the Wagner Meters Orion 950 pinless wood moisture meter, explaining its dual depth measurement, Bluetooth reporting, and where it stops being the right instrument next to a thermal camera.
Read More→
Tramex Moisture Encounter ME5 Review: The Dual-Depth Pinless Meter
A detailed look at the Tramex ME5 pinless moisture meter, centered on its dual-depth measurement and its practical limits.
Read More→
Teslong 0.21-Inch Replacement Cable Review: The First Hour With a Dual-Lens Probe
A practical review of the Teslong 5.5mm dual-lens replacement cable, covering compatibility, the first inspection, image interpretation, and where the listing leaves you guessing.
Read More→